Netgear GS110TPP

The GS110TPP is a 10-port managed gigabit switch. Eight ports support PoE+, with a standard total power budget of 120W.

Hardware build-up

To access the CPU's serial console on UART0, header J1 is available with 3.3V logic, 115200 baud, and 8n1 bits.

The internal switch connects to port 1-8, while the external phy connects to port 9-10. The external phy is linked to the SoC via a QSGMII link.

Ports 1-8 can also provide power according to 802.3.at (PoE+) and PoE is controlled by the BCM59121. PoE management is done by an auxiliary Nuvoton M0516LDN microcontroller. Communication with the Poe-CPU happens via a serial port, connected to the main CPU's UART1. Optocouplers are used to isolate the two circuits from each other and the communication frames can be sniffed from J3 (3.3V, 19200 baud, 8n1).

To indicate the global device status, two LEDs are present on the front panel. One is labelled 'PoE Max', and is likely controlled directly by the PoE MCU. The other is labeled 'Power', and is used to indicate the device status. This LED appears to be an RGB LED, although it is currently unclear how the three colours are controlled. All ports have a two-pin bi-color LED, used to indicate the link status: green for 1000M, orange for 100M. These are driven by three SN74HC164 shift registers, using 20 of the 24 outputs available. PoE status bi-color LEDs are also available, with green used to indicate the remote device is PoE powered, and orange to signal a PoE fault status. The PoE-status LEDs are driven by two SN74LV595A shift registers, also controlled by the PoE MCU.

There is also a SN74LVC125A four-port tri-state buffer whose purpose is currently unknown.

Board pictures

GPIO connections and port LEDs

Pinouts

GPIO

I2C

JTAG

MDIO

Serial console

Serial PoE control

This connector is in the PoE power domain, which is isolated from the power domain of the SoC. Be careful when connecting to this port and use a digital isolator.

Firmware

Flash layout
Name u-boot u-boot-env device-info config log firmware1 firmware2
Size 896k 64k 64k 1M 1M 14.5M 14.5M

Vendor board definition

------------------ Board Configuration ------------------

***********************************************************
 GS110TPP 8-Port Gigabit PoE+ Ethernet Smart Managed Pro Switch with 2 Copper Ports and Cloud Management
***********************************************************
============================
 Board GPIO
============================
Device  Pin  Direction  Default  Current
------- ---- ---------- -------- --------
INT     0    IN         0        1       
INT     13   OUT        1        1       
EXT     4    IN  (IN  ) 0        0       
EXT     6    IN  (IN  ) 0        0       
EXT     7    IN  (IN  ) 0        0       
EXT     10   OUT (OUT ) 0        1       
EXT     11   IN  (IN  ) 0        0       
EXT     12   IN  (IN  ) 0        0       
EXT     13   IN  (IN  ) 0        0       
EXT     14   IN  (IN  ) 0        0       
EXT     20   OUT (OUT ) 1        1       
EXT     24   OUT (OUT ) 1        1       
EXT     25   OUT (OUT ) 1        1       
EXT     27   OUT (OUT ) 0        0       
EXT     28   OUT (OUT ) 0        0       
EXT     31   OUT (OUT ) 1        1       
EXT     32   OUT (OUT ) 0        0       
EXT     34   OUT (OUT ) 1        1       

============================
 Board Configuration
============================
====== Port ==================
Type        Usr  Phy     Media       Speed          Duplex   Attr
----------- ---- ------- ----------- -------------- -------- -------
1000M       1    (0) 8   Copper      (A) ALL        Auto     1      
1000M       2    (0) 9   Copper      (A) ALL        Auto     1      
1000M       3    (0) 10  Copper      (A) ALL        Auto     1      
1000M       4    (0) 11  Copper      (A) ALL        Auto     1      
1000M       5    (0) 12  Copper      (A) ALL        Auto     1      
1000M       6    (0) 13  Copper      (A) ALL        Auto     1      
1000M       7    (0) 14  Copper      (A) ALL        Auto     1      
1000M       8    (0) 15  Copper      (A) ALL        Auto     1      
1000M       9    (0) 16  Copper      (A) ALL        Auto     0      
1000M       10   (0) 17  Copper      (A) ALL        Auto     0      


====== Button ================

------------ Reset Button
GPIO: INT_0 
Timer: 2(sec)  Action: Reboot
Timer: 5(sec)  Action: Restore Factory


====== Led ===================
System
  ON [CUSTOM]
  ON C2 [CUSTOM]
  OFF [CUSTOM]
Port
  ON [ASIC(P)]
  ON C2 [ASIC(P)]
  OFF [ASIC(P)]
  AUTO [ASIC(P)]
PoE Max
  ON [MCU]
  OFF [MCU]
  AUTO [MCU]
PoE Port
  ON [MCU]
  ON C2 [MCU]
  OFF [MCU]
  AUTO [MCU]
Cloud
  ON [CUSTOM]
  OFF [CUSTOM]


====== Reset =================
Type: GPIO
GPIO: INT_13


====== WatchDog ==============
Type: REG


====== PoE ===================

Bootloader

U-Boot is used as bootloader for this device, and has access to a modifiable u-boot-env partition. This can be used to store modified and custom environment variables.

Some realtek-specific commands are also available:

References