Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
dgs-1210-10p [2020/10/01 23:42] – biot | dgs-1210-10p [2022/04/25 15:52] (current) – Tag with JTAG svanheule | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== D-Link DGS-1210-10P (rev F) ====== | + | ====== D-Link DGS-1210-10P (rev F, R) ====== |
{{ wiki: | {{ wiki: | ||
- | The DGS-1210-10P (rev F) is a 8 + 2-port Gigabit L2 switch with up to 65 Watts of PoE power on the 8 Gigabit ports. This model is part of the [[DGS-1210 series]] line-up. | + | The DGS-1210-10P (rev F, R) is a 8 + 2-port Gigabit L2 switch with up to 65 Watts of PoE power on the 8 Gigabit ports. This model is part of the [[DGS-1210 series]] line-up. |
===== Hardware ===== | ===== Hardware ===== | ||
* [[rtl838x|RTL8380M]] SoC | * [[rtl838x|RTL8380M]] SoC | ||
- | * Macronix MX25L25635F (32MB flash) | + | * Macronix MX25L25635F (32 MiB flash) |
- | * (128MB RAM) | + | * 128 MiB (256 MiB Nanya NT5CC256M8JQ-EK on R1) RAM |
- | * [[rtl8231|RTL8231]] GPIO extender to control the port LEDs, system LED, a reset button and a mode switch button for the PoE | + | * [[rtl8231|RTL8231]] GPIO extender to control the port LEDs, system LED, SFP auxiliary signals, a reset button and a mode switch button for the PoE. Both buttons are software controlled. |
+ | * Nuvoton M0516LDE ARM microcontroller to service the PoE controller | ||
+ | * Broadcom BCM59121B0KMLG PoE controller | ||
2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. | 2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. | ||
- | Both buttons are software controlled. Power is supplied via a 5V 2A barrel connector. | ||
- | The RTL 8380M SoC has 128MB internal RAM. There is 32MB Flash memory (U19). | ||
- | A Serial header is found at J3. Pins are Vcc(3.3V, Square), TX, RX and GND. Serial connection is via 115200 baud, 8N1. | ||
- | PoE is controlled by a Broadcom BCM59121B0KMLG | + | Power is supplied |
+ | |||
+ | A Serial header is found at J8. Pins are Vcc(3.3V, Square), TX, RX and GND. Serial connection is via 115200 | ||
+ | |||
+ | The exchange between the ARM microcontroller and the RTL SoC can be snooped by connecting a logic analyzer to header J9. Square pin is 3.3V, the middle pins are TX from SoC and ARM chip respectively, | ||
==== Pin-outs ==== | ==== Pin-outs ==== | ||
=== Soc UART === | === Soc UART === | ||
- | * J3.1: VCC, 3.3V (square pad) | + | * J8.1: VCC, 3.3V (square pad) |
- | * J3.2: TX | + | * J8.2: TX |
- | * J3.3: RX | + | * J8.3: RX |
- | * J4.4: GND | + | * J8.4: GND |
=== PoE UART === | === PoE UART === | ||
Line 45: | Line 48: | ||
The board identifies as RTL8380M_INTPHY_2FIB_1G_DEMO (Port Count: 10) for the Realtek SDK. | The board identifies as RTL8380M_INTPHY_2FIB_1G_DEMO (Port Count: 10) for the Realtek SDK. | ||
- | ==== OpenWRT | + | ==== OpenWrt |
- | There is complete hardware support in an experimental | + | There is complete hardware support in an experimental |
Original features such as cable integrity tests, offloaded remote mirroring and Port-ACLs are not yet supported. | Original features such as cable integrity tests, offloaded remote mirroring and Port-ACLs are not yet supported. | ||
Line 53: | Line 56: | ||
* [[https:// | * [[https:// | ||
- | {{tag> | + | {{tag> |