dgs-1210-16

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
dgs-1210-16 [2020/09/29 20:41] – [D-Link DGS-1210-10P (rev G)] Correct page title svanheuledgs-1210-16 [2022/04/25 15:55] (current) – Tag with JTAG svanheule
Line 6: Line 6:
  
 ===== Hardware ===== ===== Hardware =====
-4 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. They can be used alternatively to the 4 GBit Ethernet uplink ports. The respective Ethernet and SFP uplink port cannot be used at the same time. It has an [[RTL8382M]] SoC with 8 built-in PHYs, and a [[RTL8231]] GPIO extender to control the port LEDs, power LED, and a reset button (software controlled). Power is supplied via a 230V AC connector. +  * [[rtl838x|RTL8382M]] SoC 
-The RTL 8382M SoC has 128MB external RAM (Nanya). There is 32MB Flash memory (U7).+  * Macronix MX25L25635F (32MB flash) 
 +  * Nanya 128MB RAM 
 +  * [[rtl8231|RTL8231]] GPIO extender to control the port LEDs, power LED, and a reset button (software controlled) 
 + 
 +4 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules. They can be used alternatively to the 4 GBit Ethernet uplink ports. The respective Ethernet and SFP uplink port cannot be used at the same time. 
 + 
 +Power is supplied via a 230V AC connector. 
 A Serial header is found at J6. Pins are Vcc(3.3V, Square), TX, RX and GND. Serial connection is via 115200 baud, 8N1. A Serial header is found at J6. Pins are Vcc(3.3V, Square), TX, RX and GND. Serial connection is via 115200 baud, 8N1.
  
Line 31: Line 38:
 The board identifies as RTL8382M_8218B_INTPHY_8214FC_DEMO for the Realtek SDK. The board identifies as RTL8382M_8218B_INTPHY_8214FC_DEMO for the Realtek SDK.
  
-==== OpenWRT Support ==== +==== OpenWrt Support ==== 
-There is complete hardware support in an experimental OpenWRT branch. Of the L2 features, port isolation, 4096 VLANs, Local Port Mirroring, EEE are supported. There is support to do a basic configuration of PoE, advanced features such as prioritizing power for ports is not supported so far. Media change is detected on the SFP cages for fibre optic cables, however after hot-swapping an SFP module, manual setup is needed. There is no support to read the SFP ID/Sensor data via I2C.+There is complete hardware support in an experimental OpenWrt branch. Of the L2 features, port isolation, 4096 VLANs, Local Port Mirroring, EEE are supported. There is support to do a basic configuration of PoE, advanced features such as prioritizing power for ports is not supported so far. Media change is detected on the SFP cages for fibre optic cables, however after hot-swapping an SFP module, manual setup is needed. There is no support to read the SFP ID/Sensor data via I2C.
 Original features such as cable integrity tests, offloaded remote mirroring and Port-ACLs are not yet supported. Original features such as cable integrity tests, offloaded remote mirroring and Port-ACLs are not yet supported.
  
Line 39: Line 46:
   * [[https://eu.dlink.com/uk/en/products/dgs-1210-series-gigabit-smart-switches| Product page ]]   * [[https://eu.dlink.com/uk/en/products/dgs-1210-series-gigabit-smart-switches| Product page ]]
  
-{{tag>dlink-dgs-1210}}+{{tag>dlink-dgs-1210}} {{tag>jtag}}
  • dgs-1210-16.1601412065.txt.gz
  • Last modified: 2020/09/29 20:41
  • by svanheule