Show pageOld revisionsBacklinksFold/unfold allBack to top This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong. ====== Zyxel GS1900-24EP ====== {{ https://www.zyxel.com/library/assets/products/gs1900-series/img_gs1900-24ep_p_1000x1000.jpg?200}} The GS1900-24EP is a 24-port Gigabit L2 switch with up to 130 Watts of PoE power on the 12 Gigabit ports ===== Hardware ===== * [[rtl838x|RTL8382M]] * Nuvoton NUC029ZAN ARM microcontroller * 2x 8-port PHY extenders * 2x [[RTL8231]] GPIO extender to control the port LEDs * Winbond W631GG8NB (128MB DDR3 SDRAM) * Winbond W25Q128JVSQ (16MB flash) Power is supplied via a 100-240V C13 connector. PoE is controlled by 2 Realtek RTL8238 PSE controllers via the Nuvoton NUC029ZAN ARM microcontroller. ==== Pinouts ==== Header JP1 has a UART: * JP1.1: 3.3V * JP1.2: TX * JP1.3: RX * JP1.4: GND Pin 1 is identified closest to the JP1 marking. Header J2 is MIPS EJTAG: * J2.1: TRST * J2.2: GND * J2.3: TDI * J2.4: GND * J2.5: TDO * J2.6: GND * J2.7: TMS * J2.8: GND * J2.9: TCK * J2.10: GND * J2.11: RST * J2.12: RTCK * J2.13: DINT * J2.14: VIO Pin 1 is identified with a white dot on opposite end to the J2 marking. ==== Board details ==== {{wiki:zyxel:zyxel_gs1900-24ep_top.jpeg?200}} {{wiki:zyxel:zyxel_gs1900-24ep_bottom.jpeg?200}} {{wiki:zyxel:zyxel_gs1900-24ep_internal.jpeg?200}} ===== Firmware ===== ==== Vendor board definition ==== <file> ------------------ Board Configuration ------------------ **************************** GS1900-24EP **************************** ============================ HW Rev.: A1 ============================ Device Pin Direction Default Current ------- ---- ---------- -------- -------- INT 0 OUT 0 0 INT 1 OUT 1 1 INT 2 OUT 0 0 INT 3 OUT 0 0 INT 8 OUT 1 1 INT 9 OUT 1 1 INT 12 IN 0 0 INT 13 OUT 1 1 INT 14 OUT 1 1 INT 15 OUT 1 1 INT 16 IN 0 0 INT 17 OUT 1 1 INT 18 OUT 0 0 INT 19 IN 0 0 INT 20 OUT 1 1 INT 21 IN 0 0 INT 22 IN 0 0 INT 23 OUT 1 1 EXT 0 IN (IN ) 0 0 EXT 1 IN (IN ) 0 1 EXT 2 IN (IN ) 0 0 EXT 3 IN (IN ) 0 1 EXT 4 IN (IN ) 0 1 EXT 5 OUT (OUT ) 1 1 EXT 6 OUT (OUT ) 1 1 EXT 7 IN (IN ) 0 1 EXT 8 OUT (OUT ) 1 1 EXT 13 OUT (OUT ) 0 0 EXT 14 OUT (OUT ) 0 0 EXT 15 OUT (OUT ) 0 0 EXT 16 OUT (OUT ) 0 0 EXT 17 OUT (IN ) 0 0 EXT 18 OUT (IN ) 0 0 EXT 21 IN (IN ) 0 0 EXT 22 IN (IN ) 0 1 EXT 23 OUT (OUT ) 0 0 EXT 24 OUT (OUT ) 0 0 EXT 25 OUT (OUT ) 0 0 EXT 26 IN (IN ) 0 1 EXT 27 IN (IN ) 0 1 EXT 28 IN (IN ) 0 1 EXT 29 OUT (OUT ) 0 0 EXT 30 OUT (OUT ) 0 0 EXT 31 OUT (OUT ) 0 0 EXT 32 IN (IN ) 0 1 EXT 33 IN (IN ) 0 1 EXT 34 OUT (OUT ) 1 1 ============================ Board GPIO ============================ Device Pin Direction Default Current ------- ---- ---------- -------- -------- INT 0 OUT 0 0 INT 1 OUT 1 1 INT 2 OUT 0 0 INT 3 OUT 0 0 INT 8 OUT 1 1 INT 9 OUT 1 1 INT 12 IN 0 0 INT 13 OUT 1 1 INT 14 OUT 1 1 INT 15 OUT 1 1 INT 16 IN 0 0 INT 17 OUT 1 1 INT 18 OUT 0 0 INT 19 IN 0 0 INT 20 OUT 1 1 INT 21 IN 0 0 INT 22 IN 0 0 INT 23 OUT 1 1 EXT 0 IN (IN ) 0 0 EXT 1 IN (IN ) 0 1 EXT 2 IN (IN ) 0 0 EXT 3 IN (IN ) 0 1 EXT 4 IN (IN ) 0 1 EXT 5 OUT (OUT ) 1 1 EXT 6 OUT (OUT ) 1 1 EXT 7 IN (IN ) 0 1 EXT 8 OUT (OUT ) 1 1 EXT 13 OUT (OUT ) 0 0 EXT 14 OUT (OUT ) 0 0 EXT 15 OUT (OUT ) 0 0 EXT 16 OUT (OUT ) 0 0 EXT 17 OUT (IN ) 0 0 EXT 18 OUT (IN ) 0 0 EXT 21 IN (IN ) 0 1 EXT 22 IN (IN ) 0 1 EXT 23 OUT (OUT ) 0 0 EXT 24 OUT (OUT ) 0 0 EXT 25 OUT (OUT ) 0 0 EXT 26 IN (IN ) 0 1 EXT 27 IN (IN ) 0 1 EXT 28 IN (IN ) 0 1 EXT 29 OUT (OUT ) 0 0 EXT 30 OUT (OUT ) 0 0 EXT 31 OUT (OUT ) 0 0 EXT 32 IN (IN ) 0 1 EXT 33 IN (IN ) 0 1 EXT 34 OUT (OUT ) 1 1 ============================ Board Configuration ============================ ====== Port ================== Type Usr Phy Media Speed Duplex Attr ---------- ---- ------- ----------- -------------- -------- ------- 1000M 1 (0) 0 Copper (A) ALL Auto 1 1000M 2 (0) 1 Copper (A) ALL Auto 1 1000M 3 (0) 2 Copper (A) ALL Auto 1 1000M 4 (0) 3 Copper (A) ALL Auto 1 1000M 5 (0) 4 Copper (A) ALL Auto 1 1000M 6 (0) 5 Copper (A) ALL Auto 1 1000M 7 (0) 6 Copper (A) ALL Auto 1 1000M 8 (0) 7 Copper (A) ALL Auto 1 1000M 9 (0) 8 Copper (A) ALL Auto 1 1000M 10 (0) 9 Copper (A) ALL Auto 1 1000M 11 (0) 10 Copper (A) ALL Auto 1 1000M 12 (0) 11 Copper (A) ALL Auto 1 1000M 13 (0) 12 Copper (A) ALL Auto 0 1000M 14 (0) 13 Copper (A) ALL Auto 0 1000M 15 (0) 14 Copper (A) ALL Auto 0 1000M 16 (0) 15 Copper (A) ALL Auto 0 1000M 17 (0) 16 Copper (A) ALL Auto 0 1000M 18 (0) 17 Copper (A) ALL Auto 0 1000M 19 (0) 18 Copper (A) ALL Auto 0 1000M 20 (0) 19 Copper (A) ALL Auto 0 1000M 21 (0) 20 Copper (A) ALL Auto 0 1000M 22 (0) 21 Copper (A) ALL Auto 0 1000M 23 (0) 22 Copper (A) ALL Auto 0 1000M 24 (0) 23 Copper (A) ALL Auto 0 ====== Button ================ ------------ Reset Button GPIO: EXT_3 Timer: 6(sec) Action: Restore Factory ====== Led =================== SYS (REG) ALARM (REG) ====== Reset ================= Type: GPIO GPIO: EXT_5 ====== WatchDog ============== Type: REG ====== PoE =================== Power Configuration -------------------------------- Nominal Power (admin) : 130000 mW Nominal Power (actual): 140000 mW Class Power Configuration -------------------------------- Class Power Limit (mW) -------- ---------------- 0 16200 1 4200 2 7400 3 16200 Port Configuration -------------------------------- LPort PoE Port Default Mode -------- -------- ---------------- 0 0.0 IEEE 802.3at 1 0.1 IEEE 802.3at 2 0.2 IEEE 802.3at 3 0.3 IEEE 802.3at 4 0.4 IEEE 802.3at 5 0.5 IEEE 802.3at 6 0.6 IEEE 802.3at 7 0.7 IEEE 802.3at 8 0.8 IEEE 802.3at 9 0.9 IEEE 802.3at 10 0.10 IEEE 802.3at 11 0.11 IEEE 802.3at LED Configuration -------------------------------- Port LED Configuration -------------------------------- Port Type Configuration -------- -------- -------------------------------- 0 SW_CTRL Entity: 2, Port 0 1 SW_CTRL Entity: 2, Port 1 2 SW_CTRL Entity: 2, Port 2 3 SW_CTRL Entity: 2, Port 3 4 SW_CTRL Entity: 2, Port 4 5 SW_CTRL Entity: 2, Port 5 6 SW_CTRL Entity: 2, Port 6 7 SW_CTRL Entity: 2, Port 7 8 SW_CTRL Entity: 2, Port 8 9 SW_CTRL Entity: 2, Port 9 10 SW_CTRL Entity: 2, Port 10 11 SW_CTRL Entity: 2, Port 11 SMI Configuration -------------------------------- Type: UART Buadrate: 19200 bps Disabled Pin Configuration -------------------------------- Type GPIO Active -------- -------- -------- DISABLE EXT_13 --- </file> ===== References ===== * [[http://www.zyxel.com/us/en/products_services/gs1900_series.shtml | Product page ]] {{tag>zyxel-gs1900}} {{tag>jtag}} gs1900-24ep.txt Last modified: 2022/05/16 03:54by raylynnknight