led_control

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
led_control [2020/12/16 21:00] – [LEDs and GPIO expanders on the RTL838x] Improve LED mode formatting svanheuleled_control [2025/01/06 19:30] (current) – Add LED modes from Realtek docs svanheule
Line 2: Line 2:
 RTL83xx-based switches typically have a large number of LEDs due to each switch port requiring at least one LED, which typically is bi-color (Green for 1000MBit, Yellow for 100/10MBit) or even tri-color (fail status or PoE). Some switches have two separate LEDs per port, others only one multi-colored LED. For controlling these LEDs, this however does not make any difference. In order to control so many different LEDs, normally a serial bus with PINs LED_CLK (122 on the RTL838x) and LED_DAT (123) is used for the port status LEDs, while a few other LEDs can be controlled directly by the SoC. In particular on the RTL838x SoCs with their very few available GPIOs, this is normally only the System LED. The power led is normally not SoC controllable. RTL83xx-based switches typically have a large number of LEDs due to each switch port requiring at least one LED, which typically is bi-color (Green for 1000MBit, Yellow for 100/10MBit) or even tri-color (fail status or PoE). Some switches have two separate LEDs per port, others only one multi-colored LED. For controlling these LEDs, this however does not make any difference. In order to control so many different LEDs, normally a serial bus with PINs LED_CLK (122 on the RTL838x) and LED_DAT (123) is used for the port status LEDs, while a few other LEDs can be controlled directly by the SoC. In particular on the RTL838x SoCs with their very few available GPIOs, this is normally only the System LED. The power led is normally not SoC controllable.
  
-There are several different ways how the LEDs can be controlled by this serial bus. The bus itself can be in SCAN mode (with different LED numbers) or SERIAL mode. In any case the serial information needs to be converted in order to drive the respective LED. There are two different converters found on the RTL83xx boards: 74HC164 shift registers and RTL8231 GPIO expanders. The shift-registers only work with the serial mode, whereas the RTL8231 supports both serial and scan mode. The scan-mode actually is an I2C-like mode, called SMI mode by Realtek.+There are several different ways how the LEDs can be controlled by this serial bus. The bus itself can be in SCAN mode (with different LED numbers) or SERIAL mode. In any case the serial information needs to be converted in order to drive the respective LED. There are two different converters found on the RTL83xx boards: 74HC164 shift registers and [[RTL8231]] GPIO expanders. The shift-registers only work with the serial mode, whereas the RTL8231 supports both serial and scan mode. The scan-mode actually is an I2C-like mode, called SMI mode by Realtek.
  
-For the RTL SoCs, the port LEDs are typically automatically controlled by the SoC (ASIC) using the serial bus. The configuration is partially defined by strapping pins, and by several LED control registers. On the RTL839x, the serial interface is initially configured by strapipng pins 156 and 157: 0b00 Serial LED mode, 0b01: SCAN single mode, 0b10: SCAN Bi-color mode, 0b11: disable LED. +For the RTL SoCs, the port LEDs are typically automatically controlled by the SoC (ASIC) using the serial bus. The configuration is partially defined by strapping pins, and by several LED control registers. On the RTL839x, the serial interface is initially configured by strapping pins 156 and 157: 
-The setup of the LED configuration is normally done by u-boot and does not need to be changed by Linux, unless manual control of the LEDs is necessary, for example if some of the port-LEDs have special purposes. u-boot configures the LEDs in ''board/Realtek/switch/rtk/mac/rtl8380/rtl8380_init.c''. The configuration values for different boards can be found in ''boot/u-boot-2011.12/board/Realtek/switch/rtk/conf/''. +  * 0b00 Serial LED mode 
-Both the RTL838x and the RTL839x have a LED control register, named RTL83XX_LED_GLB_CTRL, which allows to enable and configure the serial LED interface and control the system LED.+  * 0b01: SCAN single mode 
 +  * 0b10: SCAN Bi-color mode 
 +  * 0b11: disable LED.
  
-Manual control seems necessary in case where serially connected LEDs are not used as port-leds (such as additional status LEDs for PoE, "cloud connection" and the like). In that case it appears that the setup of all the serial LEDs is too complex to be controlled by the SoC alone. The user needs to disable SoC control over *all* the serially connected LEDs in that case. On both the RTL839x and RTL838x, software control is enabled by setting the respective bits in the RTL83XX_LED_SW_P_EN_CTRL(port) register. One of these registers holds the settings for 10 ports and 3 bits define the state of the LED:+The setup of the LED configuration is normally done by U-Boot and does not need to be changed by Linux, unless manual control of the LEDs is necessary, for example if some of the port-LEDs have special purposes. U-Boot configures the LEDs in ''board/Realtek/switch/rtk/mac/rtl8380/rtl8380_init.c''. The configuration values for different boards can be found in ''boot/u-boot-2011.12/board/Realtek/switch/rtk/conf/''. 
 +Both the RTL838x and the RTL839x have a LED control register, named ''RTL83XX_LED_GLB_CTRL'', which allows to enable and configure the serial LED interface and control the system LED. 
 + 
 +Manual control seems necessary in case where serially connected LEDs are not used as port-leds (such as additional status LEDs for PoE, "cloud connection" and the like). In that case it appears that the setup of all the serial LEDs is too complex to be controlled by the SoC alone. The user needs to disable SoC control over **all** the serially connected LEDs in that case. On both the RTL839x and RTL838x, software control is enabled by setting the respective bits in the ''RTL83XX_LED_SW_P_EN_CTRL(port)'' register. One of these registers holds the settings for 10 ports and 3 bits define the state of the LED:
   * 0x0: SoC controls LED   * 0x0: SoC controls LED
   * 0x1: One Single Color LED connected here   * 0x1: One Single Color LED connected here
   * 0x3: Bi-color LED   * 0x3: Bi-color LED
   * 0x7: Tri-color LED   * 0x7: Tri-color LED
-It is unclear why not 2 bits would be sufficient for this.+It is unclear why 2 bits would not be sufficient for this.
  
 ==== LEDs and GPIO expanders on the RTL838x ==== ==== LEDs and GPIO expanders on the RTL838x ====
  
-The power LED can be set to different blinking modes with register RTL8380_LED_MODE_SEL (0xBB001004), bits 2 and 3. Bits 0 and 1 seem to be controlled by strapping and define the way the Power LED is controlled.+The power LED can be set to different blinking modes with register ''RTL8380_LED_MODE_SEL (0xBB001004)'', bits 2 and 3. Bits 0 and 1 seem to be controlled by strapping and define the way the Power LED is controlled.
  
 === RTL8380 external LED and GPIO registers === === RTL8380 external LED and GPIO registers ===
-These registers are at a base address of 0xBB00A000.+These registers are at a base address of ''0xBB00A000''.
  
 ^ Offset ^ Name ^ Description ^ ^ Offset ^ Name ^ Description ^
 | 0x00 | [[#Global LED control|LED_GLB_CTRL]] | | | 0x00 | [[#Global LED control|LED_GLB_CTRL]] | |
 | 0x04 | [[#Port LED mode control|LED_MODE_CTRL]] | | | 0x04 | [[#Port LED mode control|LED_MODE_CTRL]] | |
-| 0x08 | LED_P_EN_CTRL | Bit mask indicating which LEDs are ASIC controlled. Bit position corresponds to the MAC/phy number. Set to 1 to enable the LED output for this phy. | +| 0x08 | ''LED_P_EN_CTRL'' | Bit mask indicating which LEDs are ASIC controlled. Bit position corresponds to the MAC/phy number. Set to 1 to enable the LED output for this phy. | 
-| 0x0C | LED_SW_CTRL | | +| 0x0C | ''LED_SW_CTRL'' | | 
-| 0x10+4×n | LED_n_SW_P_EN_CTRL | LED index n = {0, 1, 2}. Bit mask indicating which LEDs are controlled by the user. Bit position corresponds to the MAC/phy number. Set to 0 for automatic control, 1 for manual control. The corresponding bit in LED_P_EN_CTRL must also be set for this setting to be effective. |+| 0x10+4×n | ''LED_n_SW_P_EN_CTRL'' | LED index n = {0, 1, 2}. Bit mask indicating which LEDs are controlled by the user. Bit position corresponds to the MAC/phy number. Set to 0 for automatic control, 1 for manual control. The corresponding bit in LED_P_EN_CTRL must also be set for this setting to be effective. |
 | 0x1C+4×p | [[#Port LED user control|LED_SW_P_p_CTRL]] | Port index p = {0, .., 27} | | 0x1C+4×p | [[#Port LED user control|LED_SW_P_p_CTRL]] | Port index p = {0, .., 27} |
-| 0x8C + 4×i | EXT_GPIO_DIR_i_CTRL | i = floor(index/32), index = {0, .., 54} | +| 0x8C + 4×i | ''EXT_GPIO_DIR_i_CTRL'' | i = floor(index/32), index = {0, .., 54} | 
-| 0x94 + 4×i | EXT_GPIO_DATA_i_CTRL | i = floor(index/32), index = {0, .., 54} |+| 0x94 + 4×i | ''EXT_GPIO_DATA_i_CTRL'' | i = floor(index/32), index = {0, .., 54} |
 | 0x9C | [[#Extra GPIO command register|EXT_GPIO_INDIRECT_ACCESS]] | | | 0x9C | [[#Extra GPIO command register|EXT_GPIO_INDIRECT_ACCESS]] | |
-| 0xA0 | LED_LOAD_LV1 | | +| 0xA0 | ''LED_LOAD_LV1'' | | 
-| 0xA4 | LED_LOAD_LV2 | | +| 0xA4 | ''LED_LOAD_LV2'' | | 
-| 0xA8 | LED_LOAD_LV3 | |+| 0xA8 | ''LED_LOAD_LV3'' | |
 | 0xAC+4×k | [[#Port LED status registers|LED0_LO_STSk_CTRL]] | Low ports LED0 status control | | 0xAC+4×k | [[#Port LED status registers|LED0_LO_STSk_CTRL]] | Low ports LED0 status control |
 | 0xB8+4×k | [[#Port LED status registers|LED1_LO_STSk_CTRL]] | Low ports LED1 status control | | 0xB8+4×k | [[#Port LED status registers|LED1_LO_STSk_CTRL]] | Low ports LED1 status control |
Line 41: Line 46:
 | 0xD4 | [[#Port LED status registers|LED1_HI_STS_CTRL]] | High ports LED1 status control | | 0xD4 | [[#Port LED status registers|LED1_HI_STS_CTRL]] | High ports LED1 status control |
 | 0xD8 | [[#Port LED status registers|LED2_HI_STS_CTRL]] | High ports LED2 status control | | 0xD8 | [[#Port LED status registers|LED2_HI_STS_CTRL]] | High ports LED2 status control |
-| 0xDC | LED_RTCT_CTRL | | +| 0xDC | ''LED_RTCT_CTRL'' | (To confirm) Realtek Cable Test control register | 
-| 0xE0 | EXTRA_GPIO_CTRL | | +| 0xE0 | ''EXTRA_GPIO_CTRL'' | | 
-| 0xE4 | EXTRA_GPIO_DIR0 | | +| 0xE4 | ''EXTRA_GPIO_DIR0'' | | 
-| 0xE8 | EXTRA_GPIO_DIR1 | | +| 0xE8 | ''EXTRA_GPIO_DIR1'' | | 
-| 0xEC | EXTRA_GPIO_DATA0 | | +| 0xEC | ''EXTRA_GPIO_DATA0'' | | 
-| 0xF0 | EXTRA_GPIO_DATA1 | |+| 0xF0 | ''EXTRA_GPIO_DATA1'' | |
  
 === Global LED control === === Global LED control ===
-Main control register for hardware accelerated LEDs and RTL8231 access.+The SoCs have been designed with the RTL8231 LED expanders in mind as a first-class citizen. A hardware peripheral is present that can keep track of the state of one (or two on RTL93xx) RTL8231 chip(s). The SoC's have dedicated pins and controllers for this task. For rtl930x C1 `LED_MDC` and C2 `LED_MDIO` For rtl931x, AL18 `LED_MDC` and AK18 `LED_MDIO`. This does require the RTL8231 connected to only function as a LED expander. This should not be confused with the dedicated `EXT_GPIO_MDxx` pins!  
 + 
 +Main control register for hardware accelerated LEDs and [[RTL8231]] access.
  
 ^ Bits ^ Field description ^ ^ Bits ^ Field description ^
-| 0-2 | Low port LED mask. Activate an LED output for ports 0-23 by setting the respective bit. 0: no LEDs, 0x1: one LED, 0x3: two active LEDs, 0x7: three active LEDs | +| 0-2 | Low port LED mask. Activate an LED output for ports 0-23 by setting the respective bit. 0: no LEDs, 0x1: one LED, 0x3: two active LEDs, 0x7: three active LEDs. LEDs must be activated from LSB to MSB, using e.g. 0x5 to enable LED2 and LED0 may confuse the LED controller. | 
-| 3-5 | High port LED mask. Activate an LED output for ports 24-27 by setting the respective bit. 0: no LEDs, 0x1: one LED, 0x3: two active LEDs, 0x7: three active LEDs |+| 3-5 | High port LED mask. Activate an LED output for ports 24-27 by setting the respective bit. 0: no LEDs, 0x1: one LED, 0x3: two active LEDs, 0x7: three active LEDs. Should have the same value as the low-port configuration, even if the ports aren't used. |
 | 6 | MDIO-clock duty cycle for LED interface | | 6 | MDIO-clock duty cycle for LED interface |
-| 7-8 | Combo Port mode. For board RTL8382M_8218B_INTPHY_8218B_2FIB_1G_DEMO cleared to 0, for all others set to 0x2 |+| 7-8 | Combo Port mode. For board ''RTL8382M_8218B_INTPHY_8218B_2FIB_1G_DEMO'' cleared to 0, for all others set to 0x2 |
 | 9-11 | STEP1 Power on LED 2..0 | | 9-11 | STEP1 Power on LED 2..0 |
 | 12-14 | STEP2 Power on LED 2..0 | | 12-14 | STEP2 Power on LED 2..0 |
Line 72: Line 79:
 Set the LED mode for the low and high ports. Field values can be 0-31 and indicate a state matching condition. Set the LED mode for the low and high ports. Field values can be 0-31 and indicate a state matching condition.
 "Link" will turn the LED on, "Act" will briefly toggle the LED on link activity, with the default state depending on a "Link" specifier. Any speed specifier will narrow the match down to only those speeds. Activity matches only the link the LED is associated with. "Link" will turn the LED on, "Act" will briefly toggle the LED on link activity, with the default state depending on a "Link" specifier. Any speed specifier will narrow the match down to only those speeds. Activity matches only the link the LED is associated with.
-  * 0: Link/Act (same for all ports w/ link)+  * 0: Link/Act
   * 1: Link    * 1: Link 
   * 2: Act   * 2: Act
   * 3: Act Rx   * 3: Act Rx
   * 4: Act Tx   * 4: Act Tx
 +  * 5: Col/Full duplex
 +  * 6: Full duplex
   * 7: Link 1G   * 7: Link 1G
   * 8: Link 100M   * 8: Link 100M
Line 86: Line 95:
   * 14: Link/Act 1G/10M   * 14: Link/Act 1G/10M
   * 15: Link/Act 100M/10M   * 15: Link/Act 100M/10M
 +  * 16: Link 10M flashing
 +  * 17: Link 100M flashing
 +  * 18: Link 1G flashing
 +  * 19: Link 10G flashing (RTL839x)
 +  * 20: Link 10G (RTL839x)
 +  * 21: Link/Act 10G (RTL839x)
   * 31: Off   * 31: Off
  
Line 133: Line 148:
 ==== LEDs on the RTL839x ==== ==== LEDs on the RTL839x ====
 On the RTL839x ''RTL8390_LED_GLB_CTRL'' has the following bits: On the RTL839x ''RTL8390_LED_GLB_CTRL'' has the following bits:
-  * Bits 0-1: Interface selection: Defined by board config variable ''pModel->led.led_if_sel''. LED_IF_SEL_SERIAL: 0; LED_IF_SEL_SINGLE_COLOR_SCAN: 1; LED_IF_SEL_BI_COLOR_SCAN: 2+  * Bits 0-1: Interface selection: Defined by board config variable ''pModel->led.led_if_sel'': 
 +    * ''LED_IF_SEL_SERIAL'': 0 
 +    * ''LED_IF_SEL_SINGLE_COLOR_SCAN'': 1 
 +    * ''LED_IF_SEL_BI_COLOR_SCAN'': 2
   * Bits 2-3: LED number selection: Number of LEDs per port, configured from ''pModel->led.num''   * Bits 2-3: LED number selection: Number of LEDs per port, configured from ''pModel->led.num''
   * Bit 4: LED MDIO-Clock duty (cycle?)   * Bit 4: LED MDIO-Clock duty (cycle?)
Line 147: Line 165:
   * Bit 25: LED active (Low or high), Set by ''pModel->led.led_if_sel'', LED_IF_SEL_SERIAL is active low, all other active high   * Bit 25: LED active (Low or high), Set by ''pModel->led.led_if_sel'', LED_IF_SEL_SERIAL is active low, all other active high
  
-Configuration of the automatic control of the LEDs is done on this SoC through defining the function of a port LED. 3 Sets of registers define whether a Port has a Led indicating Copper functionality, Fibre or Combo port. The registers are big endian 2x32 bit registers, named RTL8390_LED_COPR_PMASK_CTRL, RTL8390_LED_FIB_PMASK_CTRL, RTL8390_LED_COMBO_PMASK_CTRL. U-Boot sets them up by copying the following configuration values over (example from a 52 port switch with 4 fibre ports, rtl8393m_demo_board.c):+Configuration of the automatic control of the LEDs is done on this SoC through defining the function of a port LED. 3 Sets of registers define whether a Port has a Led indicating Copper functionality, Fibre or Combo port. The registers are big endian 2x32 bit registers, named ''RTL8390_LED_COPR_PMASK_CTRL'', ''RTL8390_LED_FIB_PMASK_CTRL'', ''RTL8390_LED_COMBO_PMASK_CTRL''. U-Boot sets them up by copying the following configuration values over (example from a 52 port switch with 4 fibre ports, rtl8393m_demo_board.c):
 <code> <code>
     .led.led_if_sel = LED_IF_SEL_SERIAL,     .led.led_if_sel = LED_IF_SEL_SERIAL,
Line 175: Line 193:
  
 ^ Offset ^ Name ^ Description ^ ^ Offset ^ Name ^ Description ^
-| 0x0E4 | LEB_GLB_CTRL | | +| 0x0E4 | ''LEB_GLB_CTRL'' | | 
-| 0x0E8 | LED_SET_2_3_CTRL | | +| 0x0E8 | ''LED_SET_2_3_CTRL'' | | 
-| 0x0EC | LED_SET_0_1_CTRL | | +| 0x0EC | ''LED_SET_0_1_CTRL'' | | 
-| 0x0F0 + 4×k | LED_COPR_SET_k_SEL_CTRL | k = floor(port/16), port = 0-51 | +| 0x0F0 + 4×k | ''LED_COPR_SET_k_SEL_CTRL'' | k = floor(port/16), port = 0-51 | 
-| 0x100 + 4×k | LED_FIB_SET_k_SEL_CTRL | k = floor(port/16), port = 0-51 | +| 0x100 + 4×k | ''LED_FIB_SET_k_SEL_CTRL'' | k = floor(port/16), port = 0-51 | 
-| 0x110 + 4×k | LED_COPR_PMASK_k_CTRL | k = floor(port/32), port = 0-51 | +| 0x110 + 4×k | ''LED_COPR_PMASK_k_CTRL'' | k = floor(port/32), port = 0-51 | 
-| 0x118 + 4×k | LED_FIB_PMASK_k_CTRL | k = floor(port/32), port = 0-51 | +| 0x118 + 4×k | ''LED_FIB_PMASK_k_CTRL'' | k = floor(port/32), port = 0-51 | 
-| 0x120 + 4×k | LED_COMBO_k_CTRL | k = floor(port/32), port = 0-51 | +| 0x120 + 4×k | ''LED_COMBO_k_CTRL'' | k = floor(port/32), port = 0-51 | 
-| 0x128 | LED_SW_CTRL | | +| 0x128 | ''LED_SW_CTRL'' | | 
-| 0x12C + 4×n | LED_SW_P_EN_n_CTRL | n = floor(port/10), port = 0-51 | +| 0x12C + 4×n | ''LED_SW_P_EN_n_CTRL'' | n = floor(port/10), port = 0-51 | 
-| 0x144 + 4×p | LED_SW_P_p_CTRL | p = 0-51 | +| 0x144 + 4×p | ''LED_SW_P_p_CTRL'' | p = 0-51 | 
-| 0x214 + 4×i | EXT_GPIO_DIR_i_CTRL | i = floor(index/32), index = 0-56 | +| 0x214 + 4×i | ''EXT_GPIO_DIR_i_CTRL'' | i = floor(index/32), index = 0-56 | 
-| 0x21C + 4×i | EXT_GPIO_DATA_i_CTRL | i = floor(index/32), index = 0-56 | +| 0x21C + 4×i | ''EXT_GPIO_DATA_i_CTRL'' | i = floor(index/32), index = 0-56 | 
-| 0x224 | EXT_GPIO_INDIRECT_ACCESS | | +| 0x224 | ''EXT_GPIO_INDIRECT_ACCESS'' | | 
-| 0x228 | LED_LOAD_LV1_10G | | +| 0x228 | ''LED_LOAD_LV1_10G'' | | 
-| 0x22C | LED_LOAD_LV2_10G | | +| 0x22C | ''LED_LOAD_LV2_10G'' | | 
-| 0x230 | LED_LOAD_LV3_10G | | +| 0x230 | ''LED_LOAD_LV3_10G'' | | 
-| 0x234 | LED_LOAD_LV1_1G | | +| 0x234 | ''LED_LOAD_LV1_1G'' | | 
-| 0x238 | LED_LOAD_LV2_1G | | +| 0x238 | ''LED_LOAD_LV2_1G'' | | 
-| 0x23C | LED_LOAD_LV3_1G | | +| 0x23C | ''LED_LOAD_LV3_1G'' | | 
-| 0x240 | LED_LOAD_LV1_100M | | +| 0x240 | ''LED_LOAD_LV1_100M'' | | 
-| 0x244 | LED_LOAD_LV2_100M | | +| 0x244 | ''LED_LOAD_LV2_100M'' | | 
-| 0x248 | LED_LOAD_LV3_100M | | +| 0x248 | ''LED_LOAD_LV3_100M'' | | 
-| 0x24C | LED_LOAD_LV1_10M | | +| 0x24C | ''LED_LOAD_LV1_10M'' | | 
-| 0x250 | LED_LOAD_LV2_10M | | +| 0x250 | ''LED_LOAD_LV2_10M'' | | 
-| 0x254 | LED_LOAD_LV3_10M | | +| 0x254 | ''LED_LOAD_LV3_10M'' | | 
-| 0x258 | LED_P_LOAD_CTRL | | +| 0x258 | ''LED_P_LOAD_CTRL'' | | 
-| 0x25C | BUZZER_CTRL | RTL8231 buzzer settings shadow register |+| 0x25C | ''BUZZER_CTRL'' | RTL8231 buzzer settings shadow register |
  
 +=== Port LED user control ===
 +52 registers, at offsets (0x144 + 4×port). After making modifications to the registers, the new configuration need to be committed by writing 0x1 to LED_SW_CTRL.
 +This sets the SW_LED_LOAD bit, updates the output, and self-clears afterwards.
  
 +^ Bits ^ Field description ^ Field values ^
 +| 0-2 | LED0 (cop0) control | 0: off \\ 1: toggle every 32ms \\ 2: toggle every 64ms \\ 3: toggle every 128ms \\ 4: toggle every 256ms \\ 5: toggle every 512ms \\ 6: toggle every 1024ms \\ 7: on |
 +| 3-5 | LED1 (cop1) control | ::: |
 +| 6-8 | LED2 (cop2) control | ::: |
 +| 9-11 | LED3 (fib0) control | ::: |
 +| 12-14 | LED4 (fib1) control | ::: |
 +| 15-17 | LED5 (fib2) control | ::: |
 ==== LEDs on the RTL930x ==== ==== LEDs on the RTL930x ====
-These registers are at a base address of 0xBB00C400.+These registers are at a base address of ''0xBB00C400''.
  
 ^ Offset ^ Name ^ Description ^ ^ Offset ^ Name ^ Description ^
-| 0x00 | LED_GLB_CTRL | | +| 0x00 | ''LED_GLB_CTRL'' | | 
-| 0x04 | LED_PORT_NUM_CTR(port) | port: 0-27, 2 bits per port| +| 0x04 | ''LED_PORT_NUM_CTR(port)'' | port: 0-27, 2 bits per port| 
-| 0x0C | LED_SET_3_CTRL | | +| 0x0C | ''LED_SET_3_CTRL'' | | 
-| 0x10 | LED_SET_2_CTRL | | +| 0x10 | ''LED_SET_2_CTRL'' | | 
-| 0x14 | LED_SET_1_CTRL | | +| 0x14 | ''LED_SET_1_CTRL'' | | 
-| 0x18 | LED_SET_0_CTRL | | +| 0x18 | ''LED_SET_0_CTRL'' | | 
-| 0x1C | LED_PORT_COPR_SET_SEL_CTRL(port) | port = 0-27, 2 bits per port| +| 0x1C | ''LED_PORT_COPR_SET_SEL_CTRL(port)'' | port = 0-27, 2 bits per port| 
-| 0x24 | LED_PORT_FIB_SEL_CTRL(port) | port = 0-27, 2 bits per port| +| 0x24 | ''LED_PORT_FIB_SEL_CTRL(port)'' | port = 0-27, 2 bits per port| 
-| 0x2C | LED_PORT_COPR_MASK_CTRL(port) | port = 0-27, 2 bits per port| +| 0x2C | ''LED_PORT_COPR_MASK_CTRL(port)'' | port = 0-27, 2 bits per port| 
-| 0x30 | LED_PORT_FIB_MASK_CTRL(port) | port = 0-27, 2 bits per port|  +| 0x30 | ''LED_PORT_FIB_MASK_CTRL(port)'' | port = 0-27, 2 bits per port|  
-| 0x34 | LED_PORT_COMBO_MASK_CTRL(port) | port = 0-27, 1 bit per port|  +| 0x34 | ''LED_PORT_COMBO_MASK_CTRL(port)'' | port = 0-27, 1 bit per port|  
-| 0x38 | LED_SW_LED_LOAD | | +| 0x38 | ''LED_SW_LED_LOAD'' | | 
-| 0x3c | LED_PORT_SW_EN_CTRL(port) | port = 0-27, 4 bits per port | +| 0x3c | ''LED_PORT_SW_EN_CTRL(port)'' | port = 0-27, 4 bits per port | 
-| 0x4c | LED_PORT_SW_CTRL(port) | port = 0-27, 1 register per port | +| 0x4c | ''LED_PORT_SW_CTRL(port)'' | port = 0-27, 1 register per port | 
-| 0xbc | LED_INDRT_ACCESS_CTRL | standard SMI access register | +| 0xbc | ''LED_INDRT_ACCESS_CTRL'' | standard SMI access register | 
-| 0xc0 | LED_LOAD_LV1_10G | | +| 0xc0 | ''LED_LOAD_LV1_10G'' | | 
-| 0xc4 | LED_LOAD_LV2_10G | | +| 0xc4 | ''LED_LOAD_LV2_10G'' | | 
-| 0xc8 | LED_LOAD_LV3_10G | | +| 0xc8 | ''LED_LOAD_LV3_10G'' | | 
-| 0xcc | LED_LOAD_LV1_2P5G | | +| 0xcc | ''LED_LOAD_LV1_2P5G'' | | 
-| 0xd0 | LED_LOAD_LV2_2P5G | | +| 0xd0 | ''LED_LOAD_LV2_2P5G'' | | 
-| 0xd4 | LED_LOAD_LV3_2P5G | | +| 0xd4 | ''LED_LOAD_LV3_2P5G'' | | 
-| 0xd8 | LED_LOAD_LV1_1G | | +| 0xd8 | ''LED_LOAD_LV1_1G'' | | 
-| 0xdc | LED_LOAD_LV2_1G | | +| 0xdc | ''LED_LOAD_LV2_1G'' | | 
-| 0xe0 | LED_LOAD_LV3_1G | | +| 0xe0 | ''LED_LOAD_LV3_1G'' | | 
-| 0xe4 | LED_LOAD_LV1_500M | | +| 0xe4 | ''LED_LOAD_LV1_500M'' | | 
-| 0xe8 | LED_LOAD_LV2_500M | | +| 0xe8 | ''LED_LOAD_LV2_500M'' | | 
-| 0xec | LED_LOAD_LV3_500M | | +| 0xec | ''LED_LOAD_LV3_500M'' | | 
-| 0xf0 | LED_LOAD_LV1_100M | | +| 0xf0 | ''LED_LOAD_LV1_100M'' | | 
-| 0xf4 | LED_LOAD_LV2_100M | | +| 0xf4 | ''LED_LOAD_LV2_100M'' | | 
-| 0xf8 | LED_LOAD_LV3_100M | | +| 0xf8 | ''LED_LOAD_LV3_100M'' | | 
-| 0xfc | LED_LOAD_LV1_10M | | +| 0xfc | ''LED_LOAD_LV1_10M'' | | 
-| 0x100 | LED_LOAD_LV2_10M | | +| 0x100 | ''LED_LOAD_LV2_10M'' | | 
-| 0x104 | LED_LOAD_LV3_10M | | +| 0x104 | ''LED_LOAD_LV3_10M'' | | 
-| 0x108 | LED_P_LOAD_CTRL | |+| 0x108 | ''LED_P_LOAD_CTRL'' | |
  
-The extra GPIO block starts at a base address of 0xBB00BE00:+The extra GPIO block starts at a base address of ''0xBB00BE00'':
 ^ Offset ^ Name ^ Description ^ ^ Offset ^ Name ^ Description ^
-| 0x00 | EXT_GPIO_GLB_CTRL | | +| 0x00 | ''EXT_GPIO_GLB_CTRL'' | | 
-| 0x04 | EXT_GPIO_TRIG_CTRL | | +| 0x04 | ''EXT_GPIO_TRIG_CTRL'' | | 
-| 0x08 | EXT_GPIO_DIR_CTRL_1 | | +| 0x08 | ''EXT_GPIO_DIR_CTRL_1'' | | 
-| 0x0c | EXT_GPIO_DIR_CTRL_2 | | +| 0x0c | ''EXT_GPIO_DIR_CTRL_2'' | | 
-| 0x10 | EXT_GPIO_DIR_CTRL_3 | | +| 0x10 | ''EXT_GPIO_DIR_CTRL_3'' | | 
-| 0x14 | EXT_GPIO_DATA_CTRL_1 | | +| 0x14 | ''EXT_GPIO_DATA_CTRL_1'' | | 
-| 0x18 | EXT_GPIO_DATA_CTRL_2 | | +| 0x18 | ''EXT_GPIO_DATA_CTRL_2'' | | 
-| 0x1c | EXT_GPIO_DATA_CTRL_3 | | +| 0x1c | ''EXT_GPIO_DATA_CTRL_3'' | | 
-| 0x20 | EXT_GPIO_INDRT_ACCESS_CTRL | standard SMI access register |+| 0x20 | ''EXT_GPIO_INDRT_ACCESS_CTRL'' | standard SMI access register |
  • led_control.1608152444.txt.gz
  • Last modified: 2020/12/16 21:00
  • by svanheule