mestechs_msg9424

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
mestechs_msg9424 [2022/05/28 22:23] vchrizzmestechs_msg9424 [2023/02/26 15:03] (current) – Add more pictures oliver
Line 15: Line 15:
     * Winbond 25Q128JVSQ (16MB flash)     * Winbond 25Q128JVSQ (16MB flash)
     * SKhynix H5TQ4G63EFR (512MB DDR3 SDRAM)     * SKhynix H5TQ4G63EFR (512MB DDR3 SDRAM)
-    * RTL8231 GPIO extender to control the port LEDs+    * [[RTL8231]] GPIO extender to control the port LEDs
     * 3x RTL8218D 8x Gigabit PHY     * 3x RTL8218D 8x Gigabit PHY
 +    * [[https://datasheetspdf.com/pdf-file/964696/SDMC/DM2016/1|Software Protect IC DM2016]]
 +
 +4 Uplink ports are SFP+ cages which support 10GBit Base-X mini GBIC modules.
  
 ===== Pictures ===== ===== Pictures =====
  
 ==== Front ==== ==== Front ====
 +{{wiki:mestechs:img_6078.jpg?200}}
 ==== Back ==== ==== Back ====
 +{{wiki:mestechs:img_6080.jpg?200}}
 ==== Internal ==== ==== Internal ====
 +{{wiki:mestechs:img_6081.jpg?200}}
 +{{:pxl_20230218_163625714.jpg?200}}
 +{{wiki:mestechs:img_6089.jpg?200}}
 +{{wiki:mestechs:img_6112.jpg?200}}
 +{{wiki:mestechs:img_6136.jpg?200}}
 +{{:pxl_20230225_170933045.jpg?200}}
 +{{:pxl_20230225_170959496.jpg?200}}
 +{{:pxl_20230218_172419528.jpg?200}}
 +{{:pxl_20230218_172454620.jpg?200}}
 +{{:pxl_20230218_172445723.jpg?200}}
 +{{:pxl_20230225_172756640.jpg?200}}
  
 ===== Technical Information ===== ===== Technical Information =====
Line 372: Line 386:
   * put zyxel_xgs1250-12-initramfs-kernel.bin in the tftproot directory of your running tftpserver   * put zyxel_xgs1250-12-initramfs-kernel.bin in the tftproot directory of your running tftpserver
   * connect to the switch via serial (115200 baud 8n1)   * connect to the switch via serial (115200 baud 8n1)
-  * (re)boot your switch and press escape in serial terminal+  * (re)boot your switch and press escape in serial terminal in the bootloader at the prompt "Hit Esc key to stop autoboot"
   * in serial terminal run command: **rtk network on**   * in serial terminal run command: **rtk network on**
   * in serial terminal run command: **tftpboot 0x84f00000 192.168.1.2:openwrt-realtek-rtl930x-zyxel_xgs1250-12-initramfs-kernel.bin**   * in serial terminal run command: **tftpboot 0x84f00000 192.168.1.2:openwrt-realtek-rtl930x-zyxel_xgs1250-12-initramfs-kernel.bin**
Line 443: Line 457:
 RTL9300# # tftpboot 0x84f00000 192.168.1.2:openwrt-realtek-rtl930x-zyxel_xgs1250-12-initramfs-kernel.bin RTL9300# # tftpboot 0x84f00000 192.168.1.2:openwrt-realtek-rtl930x-zyxel_xgs1250-12-initramfs-kernel.bin
 Using rtl9300#0 device Using rtl9300#0 device
-TFTP from server 192.168.1.3; our IP address is 192.168.1.1+TFTP from server 192.168.1.2; our IP address is 192.168.1.1
 Filename 'openwrt-realtek-rtl930x-zyxel_xgs1250-12-initramfs-kernel.bin'. Filename 'openwrt-realtek-rtl930x-zyxel_xgs1250-12-initramfs-kernel.bin'.
 Load address: 0x84f00000 Load address: 0x84f00000
  • mestechs_msg9424.1653776599.txt.gz
  • Last modified: 2022/05/28 22:23
  • by vchrizz