zyxel_xgs1210-12

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
zyxel_xgs1210-12 [2022/06/20 13:37] – oliverzyxel_xgs1210-12 [2022/07/16 14:06] (current) – Moved to zyxel_xgs1210_series oliver
Line 1: Line 1:
-====== Zyxel XGS1210-12 and XGS1010-12 ====== +Moved to [[zyxel_xgs1210_series]]
- +
-The XGS1210-12 and XGS1010-12 are 10 + 2-port Multi-Gigabit L3 switch. They have 8 Gigabit ports, 2 2.5 Gigabit Ethernet ports and 2 SFP+ 10GBit uplink cages. +
- +
-The XGS1210-12 and XGS1010-12 only seem to differentiate in user-facing software, the hardware seems to be identical. +
- +
-===== Hardware ===== +
-  * [[rtl930x|RTL9302B]] SoC +
-  * Macronix MX25L12833F (16MB flash) +
-  * Nanja NT5CC64M16GP-1 (128MB DDR3 SDRAM) +
-  * [[RTL8231]] GPIO extender to control the port LEDs +
-  * RTL8218D 8x Gigabit PHY +
-  * 2 RTL8226 2.5 Gigabit PHYs +
- +
-2 Uplink ports are SFP+ cages which support 10GBit Base-X mini GBIC modules. +
- +
-Power is supplied via a 12V 1.5A standard barrel connector. At the right side behind the grid is UART serial connector. +
-A Serial header can be connected to from the outside of the switch trough the airvents with a standard 2.54mm header. Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial connection is via 115200 baud, 8N1. +
-==== Board details ==== +
- +
-{{wiki:zyxel:zyxel_xgs1210-12.png?200}} +
- +
- +
-===== Firmware ===== +
- +
-It ships with a u-boot bootloader (U-Boot Version V1.0.0.1 (Oct 14 2019 - 17:51:23)) based on Realtek's SDK for RTL93xx SoCs and Linux 3.18 based on Realtek's SDK 3.x. It has a web interface for all management functions. +
- +
-<code> +
-Board: RTL9300 CPU:800MHz LX:175MHz DDR:600MHz +
-DRAM:  128 MB +
-SPI-F: MXIC/C22018/MMIO16-1/ModeC 1x16 MB (plr_flash_info @ 83f6a2a4) +
-Loading 65536B env. variables from offset 0xe0000 +
-Net:   Net Initialization Skipped +
-No ethernet found. +
-Hit Esc key to stop autoboot:  0  +
- +
-RTL9300# # rtk network on +
-Enable network +
-RTCORE Driver Module Initialize +
-  IOAL init +
-  Hardware-profile probe  GPIO probe (unit 0): (found) +
-  GPIO Init +
-  RTL8231 probe (unit 0): (found) +
-  RTL8231 init (unit 0) +
- (XGS1210_12) +
-  Hardware-profile init +
-  GPIO probe (unit 0): (found) +
-  GPIO Init rtl9300_gpio_init had already been initialized! +
- +
-  SPI init (unit 0)  +
-  I2C probe (unit 0) +
-  I2C init (unit 0) +
-  RTL8231 probe (unit 0): (found) +
-  RTL8231 init (unit 0) +
- r9300_rtl8231_init had already been initialized! +
-  NIC probe (unit 0) +
-  Loader RTNIC Driver Module Initialize +
-  IOAL init +
-RTK Driver Module Initialize +
-  MAC probe (unit 0) +
-    Chip 9302 (found) +
-  MAC init (unit 0) +
-  SMI protocol probe (unit 0) +
-  PHY probe (unit 0) +
-  Chip Construct (unit 0) +
-    Chip Construct +
-    Disable PHY Polling +
-    PHY Reset +
-    MAC Construct +
-    Turn Off Serdes +
-    Serdes Construct +
-    PHY Construct +
-    Turn On Serdes +
-    Enable PHY Polling +
-    Misc +
-  PHY init (unit 0) +
-  Mgmt_dev init (unit 0)  +
-Please wait for PHY init-time ... +
- +
-RTL9300# # run loadcmd +
-Using rtl9300#0 device +
-TFTP from server 192.168.1.150; our IP address is 192.168.1.1 +
-Filename 'openwrt-rtl838x-zyxel_xgs1210-12-initramfs-kernel.bin'. +
-Load address: 0x84f00000 +
-Loading: ################################################################# +
-         ################################################################# +
-         ################################################################# +
-         ################################################################# +
-         ################################################################# +
-         ################################################################# +
-         ########################### +
-done +
-Bytes transferred = 6110544 (5d3d50 hex) +
-RTL9300# # bootm +
-## Booting kernel from Legacy Image at 84f00000 ... +
-   Image Name:   OpenWRT +
-   Created:      2020-12-02  18:53:07 UTC +
-   Image Type:   MIPS Linux Kernel Image (gzip compressed) +
-   Data Size:    6110480 Bytes = 5.8 MB +
-   Load Address: 80220000 +
-   Entry Point:  80220000 +
-   Verifying Checksum ... OK +
-   Uncompressing Kernel Image ... OK +
- +
-Starting kernel ... +
- +
-[    0.000000] Linux version 5.4.70 (birger@AMDDesktop) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14727-627da9a38c)) #0 Wed Dec 2 18:53:07 2020 +
-[    0.000000] prom_init called +
-[    0.000000] RTL838X model is 0 +
-[    0.000000] RTL839X model is 0 +
-[    0.000000] RTL93XX model is 93021001 +
-[    0.000000] SoC Type: RTL9302 +
-[    0.000000] Kernel command line:  +
-[    0.000000] printk: bootconsole [early0] enabled +
-[    0.000000] CPU0 revision is: 00019555 (MIPS 34Kc) +
-[    0.000000] plat_mem_setup called +
-[    0.000000] MIPS: machine is Zyxel XGS1210-12 Switch +
-[    0.000000] Registering _machine_restart +
-[    0.000000] NO PCI device found +
-[    0.000000] Initrd not found or empty - disabling initrd +
-[    0.000000] device_tree_init called +
-[    0.000000] Using appended Device Tree. +
-[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. +
-[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes +
-[    0.000000] Zone ranges: +
-[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff] +
-[    0.000000] Movable zone start for each node +
-[    0.000000] Early memory node ranges +
-[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff] +
-[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] +
-[    0.000000] On node 0 totalpages: 32768 +
-[    0.000000]   Normal zone: 288 pages used for memmap +
-[    0.000000]   Normal zone: 0 pages reserved +
-[    0.000000]   Normal zone: 32768 pages, LIFO batch:7 +
-[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 +
-[    0.000000] pcpu-alloc: [0] 0  +
-[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32480 +
-[    0.000000] Kernel command line: console=ttyS0,115200 +
-[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) +
-[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) +
-[    0.000000] Writing ErrCtl register=00028d08 +
-[    0.000000] Readback ErrCtl register=00028d08 +
-[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off +
-[    0.000000] Memory: 114836K/131072K available (4762K kernel code, 168K rwdata, 1060K rodata, 8724K init, 199K bss, 16236K reserved, 0K cma-reserved) +
-[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 +
-[    0.000000] NR_IRQS: 64 +
-[    0.000000] Found Interrupt controller: cpuintc (cpuintc) +
-[    0.000000] ICU Memory: b8003000 +
-[    0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0 +
-[    0.000000] CPU frequency from device tree: 700000000 +
-[    0.000000] CPU Clock: 700 MHz +
-[    0.000000] PLL control register: 0 +
-[    0.000000] Found NS16550a: uart (uart@b8002000) +
-[    0.000000] Using default baud rate: 38400 +
-[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5460744132 ns +
-[    0.000008] sched_clock: 32 bits at 350MHz, resolution 2ns, wraps every 6135667710ns +
-[    0.009618] printk: console [ttyS0] enabled +
-[    0.009618] printk: console [ttyS0] enabled +
-[    0.020076] printk: bootconsole [early0] disabled +
-[    0.020076] printk: bootconsole [early0] disabled +
-</code> +
- +
-==== OpenWrt Support ==== +
-There is experimental OpenWrt support: the device boots and the Ethernet and switch driver function. The 1 and 2.5 GBit ports work, but not the SFP+ cages. No GPIO support so far. +
- +
-===== References ===== +
-  * [[https://download.zyxel.com/GS1900-10HP/datasheet/GS1900-10HP_9.pdf | Product datasheet]] +
-  * [[https://www.st.com/en/microcontrollers-microprocessors/stm32f100rb.html | Product page of STM 32F100 ]] +
- +
-{{tag>zyxel}} {{tag>sfp_10g}} {{tag>nbase-t}} {{tag>jtag}}+
  • zyxel_xgs1210-12.1655732225.txt.gz
  • Last modified: 2022/06/20 13:37
  • by oliver