zyxel_xgs1210_series

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
zyxel_xgs1210_series [2023/04/26 21:06] – re-do GPIO section; add TX_FAULT oliverzyxel_xgs1210_series [2024/05/11 06:23] (current) – Show hidden blocks svanheule
Line 171: Line 171:
  
 === OEM bootlog === === OEM bootlog ===
-++++ Bootlog | 
 <code> <code>
 U-Boot 2011.12.(TRUNK_CURRENT)-svn99721 (Oct 24 2019 - 09:15:40) U-Boot 2011.12.(TRUNK_CURRENT)-svn99721 (Oct 24 2019 - 09:15:40)
Line 310: Line 309:
 RTK.0>  RTK.0> 
 </code> </code>
-++++ 
  
 ==== OEM tech-support ==== ==== OEM tech-support ====
-++++ sys dump | 
 <code> <code>
 RTK.0> sys dump hwp all RTK.0> sys dump hwp all
Line 536: Line 533:
 info->unitInfo[0].parsed_info=86c90000 info->unitInfo[0].parsed_info=86c90000
 </code> </code>
-++++ 
  
  
Line 552: Line 548:
 INT      6   IN         0        0        Permanently Pulled down, likely to indicate presence of U23 INT      6   IN         0        0        Permanently Pulled down, likely to indicate presence of U23
 INT      7   IN         1        1        Permanently Pulled up, likely to indicate presence of ...? INT      7   IN         1        1        Permanently Pulled up, likely to indicate presence of ...?
-I2C 8   OUT                          Shared SFP clock (SFP0/SFP1: SCK) +I2C 8   OUT                          Shared SFP clock (SFP0/SFP1: SCK) Pull-up near SFP0 
-I2C 9   I/O                          SDA0: (SFP0_SDA) +I2C 9   I/O                          SDA0: (SFP0_SDA) Pull-up near SFP0 
-I2C 10   I/O                          SDA1: (SFP1_SDA) +I2C 10   I/O                          SDA1: (SFP1_SDA) Pull-up near SFP1 
-INT     11   OUT        0        0        Transmit Disable (SFP0: TX_DIS_FX) +INT     11   OUT        0        0        Transmit Disable (SFP0: TX_DIS_FX) Pull-up near SFP0 
-INT     12   IN         0        0        Absent detection (SFP0: MOD-DEF0) +INT     12   IN         0        0        Absent detection (SFP0: MOD-DEF0) Pull-up near SFP0 
-INT     13   IN         0        0        Los of Signal (SFP0: LOS) +INT     13   IN         0        0        Los of Signal (SFP0: LOS) Pull-up near SFP0 (pull down NP option) 
-INT     14   IN         0        0        Transmit Fault (SFP0: TX_FAULT) +INT     14   IN         0        0        Transmit Fault (SFP0: TX_FAULT) Pull-up near SFP0 
-INT     15   OUT        0        0        Transmit Disable (SFP1: TX_DIS_FX) +INT     15   OUT        0        0        Transmit Disable (SFP1: TX_DIS_FX) Pull-up near SFP1 
-INT     16   IN         0        0        Absent detection (SFP1: MOD-DEF0) +INT     16   IN         0        0        Absent detection (SFP1: MOD-DEF0) Pull-up near SFP1 
-INT     17   IN         0        0        Los of Signal (SFP1: LOS)+INT     17   IN         0        0        Los of Signal (SFP1: LOS) Pull-up near SFP1 (pull down NP option)
 INT     18   IN         0        0        Permanently pulled down? Trace not found ... INT     18   IN         0        0        Permanently pulled down? Trace not found ...
 INT     19   IN         0        0        Permanently pulled down? Trace not found ... INT     19   IN         0        0        Permanently pulled down? Trace not found ...
 INT     20   OUT        0        0        Goes to U10? INT     20   OUT        0        0        Goes to U10?
-INT     21   IN         0        0        Transmit Fault (SFP1: TX_FAULT)+INT     21   IN         0        0        Transmit Fault (SFP1: TX_FAULT) Pull-up near SFP1
 INT     22   OUT        1        1        Reset_PHY? INT     22   OUT        1        1        Reset_PHY?
 INT     23   IN                           Reset Button INT     23   IN                           Reset Button
 </code> </code>
 +Note, that RS0/RS1 for both SFP's have permanent pull-ups, but also have the pull-down option.
 +Not connected/lost traces can still exist on an internal layer (Reset for example).
 +
 +== USB ==
 +While this switch has no USB ports, the USB pins appear to be on TP2 and TP3 on the bottom (to be confirmed)
  
 {{ :tech-support.rtf | Full tech-support output}} {{ :tech-support.rtf | Full tech-support output}}
Line 628: Line 629:
  
 ===== OpenWRT Bootlog ==== ===== OpenWRT Bootlog ====
-++++ Full OpenWRT Bootlog | 
 <code> <code>
 Board: RTL9300 CPU:800MHz LX:175MHz DDR:600MHz Board: RTL9300 CPU:800MHz LX:175MHz DDR:600MHz
Line 763: Line 763:
 [    0.020076] printk: bootconsole [early0] disabled [    0.020076] printk: bootconsole [early0] disabled
 </code> </code>
-++++ 
  
 ==== OpenWrt Support ==== ==== OpenWrt Support ====
  • zyxel_xgs1210_series.1682543198.txt.gz
  • Last modified: 2023/04/26 21:06
  • by oliver