Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
zyxel_xgs1250-12 [2021/10/30 13:56] – Add board pictures svanheule | zyxel_xgs1250-12 [2023/01/24 08:09] (current) – oliver | ||
---|---|---|---|
Line 2: | Line 2: | ||
The XGS1250-12 is a 11 + 1-port Multi-Gigabit L3 switch. It has 8 Gigabit ports, three 2.5/ | The XGS1250-12 is a 11 + 1-port Multi-Gigabit L3 switch. It has 8 Gigabit ports, three 2.5/ | ||
+ | |||
+ | {{ :: | ||
===== Hardware ===== | ===== Hardware ===== | ||
- | * [[rtl930x|RTL9302B]] SoC | + | * [[rtl93xx|RTL9302B]] SoC |
* Macronix MX25L12833F (16MB flash) | * Macronix MX25L12833F (16MB flash) | ||
* Winbond W613GU6MB-12 (128MB DDR3 SDRAM) | * Winbond W613GU6MB-12 (128MB DDR3 SDRAM) | ||
Line 14: | Line 16: | ||
Power is supplied via a 12V 2A standard barrel connector. At the right side behind the grid is UART serial connector. | Power is supplied via a 12V 2A standard barrel connector. At the right side behind the grid is UART serial connector. | ||
A Serial header can be connected to from the outside of the switch trough the airvents with a standard 2.54mm header. Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial connection is via 115200 baud, 8N1. | A Serial header can be connected to from the outside of the switch trough the airvents with a standard 2.54mm header. Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial connection is via 115200 baud, 8N1. | ||
- | |||
- | |||
- | ==== Board details ==== | ||
{{wiki: | {{wiki: | ||
{{wiki: | {{wiki: | ||
{{wiki: | {{wiki: | ||
+ | |||
+ | ==== JTAG ==== | ||
+ | |||
+ | The board has an unpopulated eJTAG header J2. Similar to the [[GS1900-48]], | ||
+ | * Add jumper across R155 to connect the nSRST pin. | ||
+ | * Move R156 to R151 to change the permanent pull-down into a pull-up. | ||
+ | * (optional) Modify the heatsink and add a 2×7 pin header (see picture) | ||
+ | |||
+ | The header' | ||
+ | |||
+ | {{wiki: | ||
+ | |||
+ | ==== Port numbers ==== | ||
+ | |||
+ | The RTL9302 SoC supports 24 GbE ports, and four 10G ports. | ||
+ | |||
+ | Device ports 1-8 are switch ports 0-7. | ||
+ | Device ports 9-12 are switch port 24-27. | ||
+ | |||
+ | ^ Ports ^ LED index ^ LED comment ^ | ||
+ | | 1-8 | 0 | Amber component of anti-parallel amber/lime LED. LED0 must be off. | | ||
+ | | 1-8 | 1 | Green component of anti-parallel amber/lime LED. LED1 must be off. | | ||
+ | ^ Ports ^ LED index ^ LED comment ^ | ||
+ | | 9-11 | 0 | Multi-LED selection. 0 chooses the lime/amber LEDs. 1 chooses the RGB LEDs. | | ||
+ | | 9-11 | 1 | LED0 = 0: amber, LED0 = 1: red | | ||
+ | | 9-11 | 2 | LED0 = 0: lime, LED0 = 1: green | | ||
+ | | 9-11 | 3 | LED0 = 0: (none), LED0 = 1: blue | | ||
+ | ^ Ports ^ LED index ^ LED comment ^ | ||
+ | | 12 | 0 | Blue | | ||
+ | | 12 | 1 | Lime | | ||
+ | |||
+ | ==== Board details ==== | ||
< | < | ||
+ | ------------------ Board Configuration ------------------ | ||
+ | |||
+ | **************************** | ||
+ | ZYXEL XGS1250-12 | ||
+ | **************************** | ||
+ | ============================ | ||
+ | Board GPIO | ||
+ | ============================ | ||
+ | Device | ||
+ | ------- ---- ---------- -------- -------- -------- | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | INT | ||
+ | |||
============================ | ============================ | ||
Board Configuration | Board Configuration | ||
Line 94: | Line 147: | ||
* [[https:// | * [[https:// | ||
- | {{tag> | + | {{tag> |