Differences

This shows you the differences between two versions of the page.

--- zyxel_xgs1250-12 [2021/11/12 12:30] – [Hardware] Fix link to RTL93xx hardware overview svanheule
+++ zyxel_xgs1250-12 [2023/01/24 08:09] (current) – oliver
@@ Line 2: / Line 2: @@
 The XGS1250-12 is a 11 + 1-port Multi-Gigabit L3 switch. It has 8 Gigabit ports, three 2.5/5/10GBit Ethernet ports and one SFP+ 10GBit uplink cages.
+{{ ::xgs1250.jpg?direct&600 |}}
 ===== Hardware =====
@@ Line 14: / Line 16: @@
 Power is supplied via a 12V 2A standard barrel connector. At the right side behind the grid is UART serial connector.
 A Serial header can be connected to from the outside of the switch trough the airvents with a standard 2.54mm header. Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial connection is via 115200 baud, 8N1.
-==== Board details ====
 {{wiki:zyxel:xgs1250-12-top.jpg?200}}
 {{wiki:zyxel:xgs1250-12-bottom.jpg?200}}
 {{wiki:zyxel:xgs1250-12-rtl8231.jpg?200}}
+==== JTAG ====
+The board has an unpopulated eJTAG header J2. Similar to the [[GS1900-48]], nSRST and nTRST are configured such that the port is disabled. The following modifications make use of the eJTAG port possible:
+  * Add jumper across R155 to connect the nSRST pin.
+  * Move R156 to R151 to change the permanent pull-down into a pull-up.
+  * (optional) Modify the heatsink and add a 2×7 pin header (see picture)
+The header's VIO pin is a voltage reference, tied to VCC via a 1k resistor (R153). This pin cannot be used to source current and is only provided as voltage reference.
+{{wiki:zyxel:xgs1250-12-jtag-heatsink.jpg?400}}
+==== Port numbers ====
+The RTL9302 SoC supports 24 GbE ports, and four 10G ports.
+Device ports 1-8 are switch ports 0-7.
+Device ports 9-12 are switch port 24-27.
+^ Ports ^ LED index ^ LED comment ^
+| 1-8   | 0 | Amber component of anti-parallel amber/lime LED. LED0 must be off. |
+| 1-8   | 1 | Green component of anti-parallel amber/lime LED. LED1 must be off. |
+^ Ports ^ LED index ^ LED comment ^
+| 9-11  | 0 | Multi-LED selection. 0 chooses the lime/amber LEDs. 1 chooses the RGB LEDs. |
+| 9-11  | 1 | LED0 = 0: amber, LED0 = 1: red |
+| 9-11  | 2 | LED0 = 0: lime, LED0 = 1: green |
+| 9-11  | 3 | LED0 = 0: (none), LED0 = 1: blue |
+^ Ports ^ LED index ^ LED comment ^
+| 12    | 0 | Blue |
+| 12    | 1 | Lime |
+==== Board details ====
 <file>
@@ Line 116: / Line 147: @@
   * [[https://download.zyxel.com/XGS1250-12/datasheet/XGS1250-12_2.pdf | Product datasheet]]
-{{tag>zyxel}} {{tag>sfp_10g}} {{tag>nbase-t}}
+{{tag>zyxel}} {{tag>sfp_10g}} {{tag>nbase-t}} {{tag>jtag}}