Differences

This shows you the differences between two versions of the page.

--- zyxel_xs1930_series [2022/06/15 04:51] – beadon
+++ zyxel_xs1930_series [2022/11/15 15:48] (current) – Remove trailing space pmenzel
@@ Line 6: / Line 6: @@
 | XS1930-10 | 8 | 2 | - |
 | XS1930-12HP | 10 | 2 | 8 |
+| XS1930-12F | 2 | 10 | - |
 ===== Models =====
@@ Line 18: / Line 19: @@
   * 3-pin fan
-The serial port is accessible via pins from from the outside on the right side of the device. Pins are front to back: GND, TX, RX, Vcc.
+The serial port is accessible via pins from the outside on the right side of the device. Pins are front to back: GND, TX, RX, Vcc.
 Port settings are 115200 baud, 8n1, with 3.3V logic level.
-If you are using a raspberryPi, ensure that the serial port is activated first, many guides list these steps, here is a decent guide : https://www.engineersgarage.com/articles-raspberry-pi-serial-communication-uart-protocol-ttl-port-usb-serial-boards/
+If you are using a Raspberry Pi, ensure that the serial port is activated first, many guides list these steps, here is a decent guide: https://www.engineersgarage.com/articles-raspberry-pi-serial-communication-uart-protocol-ttl-port-usb-serial-boards/
 Once wired up, and the serial port is enabled test that this works.  Confirm the system can use the port.
-$ setserial -g /dev/ttyS[0123]
-/dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
+  $ setserial -g /dev/ttyS[0123]
-/dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3
-/dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
+  /dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
-/dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3
+  /dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3
+  /dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
+  /dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3
 It's likely /dev/ttyS0, use Linux's cli, 'cu'
-$ cu -l /dev/ttyS0 -s 115200
+  $ cu -l /dev/ttyS0 -s 115200
 If done correctly, you will be presented with a login prompt, the login credentials for the web interface and this serial interface are the same.  Test that the system is wired properly before restarting.  Quite from cu with ~.  , that's a tilde, followed by a period.
@@ Line 377: / Line 379: @@
 A very initial boot of OpenWrt looks like this:
 <code>
-        [    0.000000] Calling smp_setup_processor_id
+    [    0.000000] Calling smp_setup_processor_id
     [    0.000000] Calling boot_cpu_init
     [    0.000000] Linux version 5.4.70 (birger@AMDDesktop) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14727-627da9a38c)) #0 Thu Oct 29 18:33:33 2020