Netgear MS510 series

• SoC: RTL9313
• RAM: 256MB DDR3L (Winbond W623GU6NB-11)
• Flash: 32MB NOR (MX25L25645G)
• Ethernet phys:
  • 1× BCM8488 with MX25U4033E flash, for 10G ports
  • 4× RTL8221B, for 2.5G ports
• Miscellaneous:
  • TMP1075 (U20) I2C temperature sensor, between UART header and SFP+ cage
  • ADT747 (U39) I2C fan control
  • 74LVC1G332 (U16) for fan sense-pin OR
• Front panel:
  • 2× LED: 'Power' and 'Fan'
  • Reset button

MS510TXM# show tech-support board     

------------------ Board Configuration ------------------

***********************************************************
 MS510TXM 8-Port Multi-Gigabit/10G Ethernet Smart Managed Pro Switch with 2 SFP+ Ports
***********************************************************
============================
 Board GPIO
============================
Device  Pin  Direction  Default  Current
------- ---- ---------- -------- --------
INT     0    OUT        1        0       
INT     1    IN         0        0       
INT     2    IN         0        0       
INT     3    IN         0        0       
INT     4    OUT        1        1       
INT     5    OUT        0        0       
INT     6    IN         1        1       
INT     7    IN         1        1       
INT     8    IN         1        1       
INT     9    IN         1        1       
INT     10   OUT        0        0       
INT     11   OUT        0        0       
INT     12   OUT        1        1       
INT     13   OUT        1        1       
INT     14   OUT        1        0       
INT     15   IN         1        1       
INT     16   IN         1        1       
INT     21   IN         1        0       
INT     22   IN         1        0       
INT     28   IN         1        1       
INT     29   OUT        1        1       

============================
 Board Configuration
============================
====== Port ==================
Type        Usr  Phy     Media       Speed          Duplex   Attr
----------- ---- ------- ----------- -------------- -------- -------
2500M       1    (0) 0   Copper      (A) ALL        Auto     0      
2500M       2    (0) 8   Copper      (A) ALL        Auto     0      
2500M       3    (0) 16  Copper      (A) ALL        Auto     0      
2500M       4    (0) 24  Copper      (A) ALL        Auto     0      
10G         5    (0) 32  Copper      (A) ALL        Auto     c      
10G         6    (0) 40  Copper      (A) ALL        Auto     c      
10G         7    (0) 48  Copper      (A) ALL        Auto     c      
10G         8    (0) 50  Copper      (A) ALL        Auto     c      
10G         9    (0) 54  Fiber       (F) 10G        (F) Full 0      
10G         10   (0) 55  Fiber       (F) 10G        (F) Full 0      


====== Fiber =================
Fiber Port Number: 2

------------ Fiber Detect
LPort  Present  MediaChg  OE Status              LOS Status
------ -------- --------- ---------------------- ----------------------
8      OE       LOS       Enabled  (GPIO:INT_7 ) Enabled  (GPIO:INT_9 )
9      OE       LOS       Enabled  (GPIO:INT_6 ) Enabled  (GPIO:INT_8 )

------------ Fiber Optical
LPort  I2C DEV  I2C TYPE  ID    Delay   SCK    SDA
------ -------- --------- ----- ------- ------ ------
8      0        8 BITS    0x50  50      INT_13 INT_16
9      1        8 BITS    0x50  50      INT_13 INT_15

------------ Fiber TX Disable
LPort  Method
------ ------
8      GPIO(INT_11)
9      GPIO(INT_10)


====== Button ================

------------ Reset Button
GPIO: INT_28
Timer: 2(sec)  Action: Reboot
Timer: 5(sec)  Action: Restore Factory
Timer: 10(sec)  Action: Restore FacReg


====== Led ===================
SYSTEM
  ON [GPIO(D)]
  OFF [GPIO(D)]
Port
  ON [ASIC(P)]
  ON C2 [ASIC(P)]
  OFF [ASIC(P)]
  AUTO [ASIC(P)]
Cloud
  ON [GPIO(D)]
  OFF [GPIO(D)]


====== Reset =================
Type: GPIO
GPIO: INT_29


====== WatchDog ==============
Type: REG